Router veznem, zapnem a nič. Zelená status LEDka bliká a krabica nekrabicuje. Čo čil?
Diagnóza
Čo človek spraví, ak bezdisplejová vec nekomunikuje? Navalí tomu UART.
Krabicu rozebrať, nájsť UART. Súdruzi ze Synology/BCM nám nehali né len místo na header, ale aj header samotný.
- Aha, tu je UART. Prvý pin zem, druhý (cyanový kábel) je RX, tretí (modrý kábel) je TX
To by bolo jennoduché, baud používajú 115200, takže tam o tom žádna.
Výstup z U-Bootu:
Code: Select all
picocom v3.1
port is : /dev/tty.usbserial-A50285BI
flowcontrol : none
baudrate is : 115200
parity is : none
databits are : 8
stopbits are : 1
escape is : C-a
local echo is : no
noinit is : no
noreset is : no
hangup is : no
nolock is : no
send_cmd is : sz -vv
receive_cmd is : rz -vv -E
imap is :
omap is :
emap is : crcrlf,delbs,
logfile is : none
initstring : none
exit_after is : not set
exit is : no
Type [C-a] [C-h] to see available commands
Terminal ready
U-Boot 2012.10-gf49bef7 (Mar 18 2016 - 17:01:18)
DEV ID = 0xcf1e
PCIE CFG DEV ID = 0x8022
OTP offset(0x8): 0x78f01c01
OTP offset(0x9): 0xfe280818
OTP offset(0xa): 0xc01b0
OTP offset(0xb): 0x0
OTP offset(0xc): 0x4400000
OTP offset(0xd): 0xbcede230
OTP offset(0xe): 0x1035b17f
OTP offset(0xf): 0x800
ProgramCoreRailVoltageFromOTPAVSCode entry
avs_code programmed 78f01c01
avs_code programmed right shifted 00000011 00000000
Setting core voltage 520e0020 0
ProgramCoreRailVoltageFromOTPAVSCode exit
NSP 16-bit DDR
SKU ID = 0x0
DDR type: DDR3
MEMC 0 DDR speed = 800MHz
PHY revision version: 0x00004005
ddr_init2: Calling soc_ddr40_set_shmoo_dram_config
ddr_init2: Calling soc_ddr40_phy_calibrate
C01. Check Power Up Reset_Bar
C02. Config and Release PLL from reset
C03. Poll PLL Lock
C04. Calibrate ZQ (ddr40_phy_calib_zq)
C05. DDR PHY VTT On (Virtual VTT setup) DISABLE all Virtual VTT
C06. DDR40_PHY_DDR3_MISC
C07. VDL Calibration
C07.1
C07.2
C07.4
C07.4.1
C07.4.4
VDL calibration result: 0x30000003 (cal_steps = 0)
C07.4.5
C07.4.6
C07.5
C08. DDR40_PHY_DDR3_MISC : Start DDR40_PHY_RDLY_ODT....
C09. Start ddr40_phy_autoidle_on (MEM_SYS_PARAM_PHY_AUTO_IDLE) ....
C10. Wait for Phy Ready...Done.
DDR phy calibration passed
Programming controller register
ddr_init2: MemC initialization complete
Validate Shmoo parameters stored in flash ..... OK
Press Ctrl-C to run Shmoo ..... skipped
Restoring Shmoo parameters from flash ..... done
Running simple memory test ..... OK
DeepSleep wakeup: ddr init bypassed 3
DDR Interface Ready
DRAM: 16 MiB
U-Boot 2012.10-gf49bef7 (Mar 18 2016 - 17:01:18)
DEV ID = 0xcf1e
PCIE CFG DEV ID = 0x8022
OTP offset(0x8): 0x78f01c01
OTP offset(0x9): 0xfe280818
OTP offset(0xa): 0xc01b0
OTP offset(0xb): 0x0
OTP offset(0xc): 0x4400000
OTP offset(0xd): 0xbcede230
OTP offset(0xe): 0x1035b17f
OTP offset(0xf): 0x800
ProgramCoreRailVoltageFromOTPAVSCode entry
avs_code programmed 78f01c01
avs_code programmed right shifted 00000011 00000000
Setting core voltage 520e0020 0
ProgramCoreRailVoltageFromOTPAVSCode exit
NSP 16-bit DDR
SKU ID = 0x0
DDR type: DDR3
MEMC 0 DDR speed = 800MHz
PHY revision version: 0x00004005
ddr_init2: Calling soc_ddr40_set_shmoo_dram_config
ddr_init2: Calling soc_ddr40_phy_calibrate
C01. Check Power Up Reset_Bar
C02. Config and Release PLL from reset
C03. Poll PLL Lock
C04. Calibrate ZQ (ddr40_phy_calib_zq)
C05. DDR PHY VTT On (Virtual VTT setup) DISABLE all Virtual VTT
C06. DDR40_PHY_DDR3_MISC
C07. VDL Calibration
C07.1
C07.2
C07.4
C07.4.1
C07.4.4
VDL calibration result: 0x30000003 (cal_steps = 0)
C07.4.5
C07.4.6
C07.5
C08. DDR40_PHY_DDR3_MISC : Start DDR40_PHY_RDLY_ODT....
C09. Start ddr40_phy_autoidle_on (MEM_SYS_PARAM_PHY_AUTO_IDLE) ....
C10. Wait for Phy Ready...Done.
DDR phy calibration passed
Programming controller register
ddr_init2: MemC initialization complete
Validate Shmoo parameters stored in flash ..... OK
Press Ctrl-C to run Shmoo ..... skipped
Restoring Shmoo parameters from flash ..... done
Running simple memory test ..... OK
DeepSleep wakeup: ddr init bypassed 3
DDR Interface Ready
DRAM: 16 MiB
WARNING: Caches not enabled
NAND: NAND_FLASH_DEVICE_ID_ADDR = 18026194
Done that
(ONFI), rv=3 iProc NAND chip could not be initialized
0 MiB
MMC: In board_mmc_init, mmc = 0xecc098
In mmc_register : mmc address : 0xf47884
In mmc_register : mmc address : 0xf47a0c
In mmc_register : mmc address : 0xf476b0
iproc_mmc: 0
SF: Detected M25P80 with page size 64 KiB, total 1 MiB
soc_pcie_hw_init : port->reg_base = 0x18012000 , its value = 0x1
PCIe port 0 in RC mode
pos is 172
==>PCIE: LINKSTA reg 0xbe val 0x9012
**************
port 0 is active!!
**************
membase 0x8000000 memlimit 0x10000000
Extended Config
i=0 <0> 0x14e4 0x8022 0x0146 0x0010 0x0011 0x0200 0x0000 0x0001
i=8 <8> 0x0000 0x0000 0x0000 0x0000 0x0100 0x0004 0x0000 0x0000
i=16 <10> 0x0800 0x1000 0x0001 0x0001 0x0000 0x0000 0x0000 0x0000
i=24 <18> 0x0000 0x0000 0x0048 0x0000 0x0000 0x0000 0x01a9 0x0000
i=32 <20> 0x0000 0x0000 0x0000 0x0000 0xac01 0xc803 0x2008 0x0000
i=40 <28> 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
i=48 <30> 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
i=56 <38> 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
i=64 <40> 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
i=72 <48> 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
i=80 <50> 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0010 0x0042
i=88 <58> 0x8000 0x0000 0x2c10 0x0010 0x5c12 0x0065 0x0000 0x9012
i=96 <60> 0x0000 0x0000 0x0000 0x0040 0x0000 0x0001 0x0000 0x0000
i=104 <68> 0x001f 0x0008 0x0000 0x0000 0x0000 0x0000 0x0002 0x0000
i=112 <70> 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
i=120 <78> 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
Standard Config
i=0 <0> 0x43a114e4 0x00100146 0x02800003 0x00000000
i=4 <4> 0x08000004 0x00000000 0x08200004 0x00000000
i=8 <8> 0x00000000 0x00000000 0x00000000 0x066114e4
i=12 <c> 0x00000000 0x00000048 0x00000000 0x000001a9
i=16 <10> 0x00000000 0x00000000 0xfe035801 0x00004108
i=20 <14> 0x00000000 0x00000000 0x00806805 0x00000000
i=24 <18> 0x00000000 0x00000000 0x0044ac09 0x00000101
i=28 <1c> 0x18103000 0x00000000 0x00000000 0x00000000
i=32 <20> 0x18003000 0x00000000 0x00000000 0x00000000
i=36 <24> 0x00000000 0x00000200 0x00000000 0x00000000
i=40 <28> 0x00000000 0x00000000 0x00010040 0x00020010
i=44 <2c> 0x00008f81 0x00102c10 0x0046dc12 0x10120000
i=48 <30> 0x00000000 0x00000000 0x00000000 0x00000000
i=52 <34> 0x0008081f 0x00000000 0x00000000 0x00000001
i=56 <38> 0x00000000 0x00000000 0x00000000 0x00000000
i=60 <3c> 0x00000000 0x00000000 0x00000000 0x00000000
BAR-0: 0x08000004
BAR-1: 0x00000000
BAR-2: 0x08200004
BAR-3: 0x00000000
BAR-4: 0x00000000
BAR-5: 0x00000000
00:00.00 - 14e4:43a1 - Network controller
pci_iproc_init_board : hose->last_busno = 0x0
Done PCI initialization
In: serial
Out: serial
Err: serial
Synology Model: RT1900acv20
org axi_clk=500MHz
iproc_get_axi_clk: refclk(0x17d7840), ndiv(0x3c) pdiv(0x1) mdiv(0x3): AXICLK:(0x1dcd6500)
arm_clk=1000MHz, axi_clk=500MHz, apb_clk=125MHz, arm_periph_clk=500MHz
Enabling icache and dcache
Enabling l2cache
Set GPIO mask: [000290c4] as GPIO_GENERAL
Re-programming LCPLL post-divider channel for CH1... done!
Net: Registering eth
Broadcom BCM IPROC Ethernet driver 0.1
Using GMAC1 (0x18023000)
et0: ethHw_chipAttach: Chip ID: 0xcf1e; phyaddr: 0x1e
bcm_robo_attach: devid: 0x2
bcmiproc_eth-0
*********************************************************
Please add diag support DIAGS_BOARD to:
BCM953022K
BCM953025K
BCM953025K_REV2
BCM958622HR
BCM958623HR
BCM958522ER
BCM958625HR
in env before you can run any diags
*********************************************************
COM2 is not configured due to board type
COM3 is not configured due to board type
========== relocate address: 0xf1c000, offset 0xe2f1c000 ==========
Press Ctrl+C to abort autoboot in 3 second
Reset Done
iproc_mmc_send_cmd() returned timeout
iproc_mmc_send_cmd() returned timeout
..Loading file "zImage" from mmc device 0:1
.............iproc_mmc_send_cmd: error during transfer: 0x00108001
** ext4fs_devread read error - block
** Unable to read "zImage" from mmc 0:1 **
ext2load - load binary file from a Ext2 filesystem
Usage:
ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
- load binary file 'filename' from 'dev' on 'interface'
to address 'addr' from ext2 filesystem
iproc_mmc_send_cmd() returned timeout
set read bl len failed
** Can't read partition table on 0:0 **
** Invalid partition 1 **
ext2load - load binary file from a Ext2 filesystem
Usage:
ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
- load binary file 'filename' from 'dev' on 'interface'
to address 'addr' from ext2 filesystem
## Booting kernel from Legacy Image at 61007fc0 ...
Image Name: Linux-3.6.11+
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3388040 Bytes = 3.2 MiB
Load Address: 61008000
Entry Point: 61008000
Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
iproc_mmc_send_cmd() returned timeout
set read bl len failed
** Can't read partition table on 0:0 **
** Invalid partition 3 **
ext2load - load binary file from a Ext2 filesystem
Usage:
ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
- load binary file 'filename' from 'dev' on 'interface'
to address 'addr' from ext2 filesystem
iproc_mmc_send_cmd() returned timeout
set read bl len failed
** Can't read partition table on 0:0 **
** Invalid partition 3 **
ext2load - load binary file from a Ext2 filesystem
Usage:
ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
- load binary file 'filename' from 'dev' on 'interface'
to address 'addr' from ext2 filesystem
## Booting kernel from Legacy Image at 61007fc0 ...
Image Name: Linux-3.6.11+
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3388040 Bytes = 3.2 MiB
Load Address: 61008000
Entry Point: 61008000
Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
u-boot> Živého či mrtvého, Jožina kdo přivede...
Dcéru a půl JZD síce nemám, ale Jožina máme momentálne ani v jednom z úplne očakávaných.
Kukal som help, súdruzi tam napakuvali snáď šecko čo existuje.
Code: Select all
u-boot> help
? - alias for 'help'
base - print or set address offset
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
chpart - change active partition
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
dhcp - boot image via network using DHCP/TFTP protocol
diag - perform board diagnostics
echo - echo args to console
env - environment handling commands
exit - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
false - do nothing, unsuccessfully
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
go - start application at address 'addr'
help - print command description/usage
i2c - I2C sub-system
itest - return true/false on integer compare
license - print GPL license text
loop - infinite loop on address range
md - memory display
mdc - memory display cyclic
mm - memory modify (auto-incrementing address)
mmc - MMC sub system
mmcinfo - display MMC info
mtdparts- define flash/nand partitions
mtest - simple RAM read/write test
mw - memory write (fill)
mwc - memory write cyclic
nand - NAND sub-system
nboot - boot from NAND device
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
pci - list and access PCI Configuration Space
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
sf - SPI flash sub-system
showvar - print local hushshell variables
sleep - delay execution for some time
source - run script from memory
sspi - SPI utility command
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
true - do nothing, successfully
usb - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker versionEšte ale najprv printenv:
Code: Select all
u-boot> env print
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200 ip=off maxcpus=2 mem=240M initrd= root=/dev/mmcblk0p5 rootdelay=0 rw syno_rescue=1 syno_hw_version=RT1900acv20 netif_num=2 syno_mac_address_mapping=eth0,eth1,wlan0,wlan1 wireless_num=2 rcutree.rcu_cpu_stall_suppress=1 syno_disable_usb3=1 flash_size=1
bootcmd=run syno_bootargs; run bootmmc
bootdelay=3
bootfile=uImage
bootmmc=mmc rescan;ext2load mmc 0:1 $kload zImage;ext2load mmc 0:1 $rload rd.bin;bootm ${kload} ${rload}; run bootresc
bootresc=setenv syno_extra_args syno_rescue=1; run syno_bootargs; ext2load mmc 0:3 $kload zImage;ext2load mmc 0:3 $rload rd.bin;bootm ${kload} ${rload}
bootspi=usb reset; ext2load usb 0:1 ${kload} zImage; ext2load usb 0:1 ${rload} rd.bin; bootm ${kload} ${rload}
brcmtag=1
console=ttyS0
emmc=1
eth1addr=d4:ae:52:bc:a5:09
eth2addr=d4:ae:52:bc:a5:0a
eth3addr=d4:ae:52:bc:a5:0b
ethact=bcmiproc_eth-0
ethaddr=d4:ae:52:bc:a5:08
hostname=northstar
ipaddr=192.168.0.1
kload=0x61007fc0
ledbh10=7
loadaddr=0x90000000
loglevel=7
manvlan1ports=4 5u 7u
manvlan2ports=2 3u
manvlan3ports=0 1u
mmc_name=004GE
rload=0x62007fc0
sdhci_maxclk=25000000
serverip=192.168.0.10
stderr=serial
stdin=serial
stdout=serial
syno_boot_delay=0
syno_boot_dev=/dev/mmcblk0p5
syno_bootargs=setenv bootargs console=ttyS0,115200 ip=off maxcpus=2 mem=240M initrd=$loadaddr_rootfs root=$syno_boot_dev rootdelay=$syno_boot_delay rw $syno_extra_args syno_hw_version=$syno_hw_version netif_num=$syno_net_if_num syno_mac_address_mapping=$syno_mac_mapping wireless_num=$syno_wireless_num rcutree.rcu_cpu_stall_suppress=1 syno_disable_usb3=${syno_disable_usb3} flash_size="1"
syno_disable_usb3=1
syno_extra_args=syno_rescue=1
syno_hdd_powerup_seq=2
syno_hw_version=RT1900acv20
syno_mac_mapping="eth0,eth1,wlan0,wlan1"
syno_net_if_num=2
syno_wireless_num=2
synover=f49bef7
uvlan1ports=0 7u
uvlan2ports=4 5u
vlan1ports=1 2 3 4 7u
vlan2ports=0 5u
Environment size: 2011/65532 bytesCode: Select all
u-boot> mmcinfo
Device: iproc_mmc
Manufacturer ID: 11
OEM: 100
Name: 004GE
Rd Block Len: 512
MMC version 4.0
High Capacity: Yes
Capacity: 3.7 GiB
Bus Width: 8-bit
Clock: 50MHz
Zháňaní firmwaru
Firmware má Synology našťastí furt na ich stránke toť tu. Poskytujú ho jak .pat, čo je vlastne iba premenuvaný tar. Asi sa sťú hrať na zaujímavých.
V tare je takáto štruktúra:
Code: Select all
SRM_RT1900ac_8227:
checksum.syno
hda1_us.tgz
hda1.tgz
indexdb.tgz
packages:
SafeAccess-northstarplus-1.2.4-0244.spk
rd.bin
synohdpack_img.tgz
uboot_do_upd.sh
uboot_RT1900acv10.bin
uboot_RT1900acv20.bin
updater
VERSION
zImage
Zlepením toho čo som už čil vedel a toho čo som čil zisteu som si polepeu rádek príkazov pre U-Boot, kerými som načítal kernel s ramdiskom z USBčka namísto interného eMMC.
Vyzíra voláko takto:
Code: Select all
usb start; usb storage; run syno_bootargs; fatload usb 0 $kload srm_rt1900ac_8227/zImage; fatload usb 0 $rload srm_rt1900ac_8227/rd.bin; boot ${kload} ${rload}; run bootrescŠtartujeme jadro, len.. čo je zas hento?
Code: Select all
(Re)start USB...
USB: Before reset, USB clk enable register is: 000003fc
Before reset, USB clk enable register is: 000003fd
usb2_reset_state is: 00000001
Bring usb2h_out of reset.......
usb2_reset_state is set and now it is: 00000000
Register 1212 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
3 Storage Device(s) found
Device 0: Vendor: SanDisk Rev: 1.00 Prod: Cruzer Blade
Type: Removable Hard Disk
Capacity: 14664.0 MB = 14.3 GB (30031872 x 512)
Device 1: Vendor: Generic Rev: 9910 Prod: STORAGE DEVICE
Type: Removable Hard Disk
Capacity: not available
Device 2: Vendor: Generic Rev: 9910 Prod: STORAGE DEVICE
Type: Removable Hard Disk
Capacity: not available
reading srm_rt1900ac_8227/zImage
................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
3388104 bytes read
reading srm_rt1900ac_8227/rd.bin
.........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
3604246 bytes read
Unknown command 'boot' - try 'help'
** Bad device size - mmc 0 **
ext2load - load binary file from a Ext2 filesystem
Usage:
ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
- load binary file 'filename' from 'dev' on 'interface'
to address 'addr' from ext2 filesystem
** Bad device size - mmc 0 **
ext2load - load binary file from a Ext2 filesystem
Usage:
ext2load <interface> <dev[:part]> [addr] [filename] [bytes]
- load binary file 'filename' from 'dev' on 'interface'
to address 'addr' from ext2 filesystem
## Booting kernel from Legacy Image at 61007fc0 ...
Image Name: Linux-3.6.11+
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3388040 Bytes = 3.2 MiB
Load Address: 61008000
Entry Point: 61008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 62007fc0 ...
Image Name: synology_northstarplus_rt1900ac
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 3604182 Bytes = 3.4 MiB
Load Address: 61008000
Entry Point: 61008000
Verifying Checksum ... OK
XIP Kernel Image ... OK
OK
boot_prep_linux commandline: console=ttyS0,115200 ip=off maxcpus=2 mem=240M initrd= root=/dev/mmcblk0p5 rootdelay=0 rw syno_rescue=1 syno_hw_version=RT1900acv20 netif_num=2 syno_mac_address_mapping=eth0,eth1,wlan0,wlan1 wireless_num=2 rcutree.rcu_cpu_stall_suppress=1 syno_disable_usb3=1 flash_size=1
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] INFO-Cygnus:472:start_kernel() entry
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.6.11+ (root@build3) (gcc version 4.9.3 20150311 (prerelease) (crosstool-NG 1.20.0) ) #8227 SMP Mon Apr 24 14:21:56 CST 2023
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Broadcom iProc
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c099d000 s6784 r8192 d13696 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60840
[ 0.000000] Kernel command line: console=ttyS0,115200 ip=off maxcpus=2 mem=240M initrd= root=/dev/mmcblk0p5 rootdelay=0 rw syno_rescue=1 syno_hw_version=RT1900acv20 netif_num=2 syno_mac_address_mapping=eth0,eth1,wlan0,wlan1 wireless_num=2 rcutree.rcu_cpu_stall_suppress=1 syno_disable_usb3=1 flash_size=1
[ 0.000000] Synology Hardware Version: RT1900acv20-j
[ 0.000000] Internal netif num: 2
[ 0.000000] Synology MAC address Mapping: eth0,eth1,wlan0,wlan1
[ 0.000000] Internal wireless num: 2
[ 0.000000] Factory USB3 Disable: 1
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 240MB = 240MB total
[ 0.000000] Memory: 232136k/232136k available, 13624k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xcf800000 - 0xff000000 ( 760 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0621000 (6244 kB)
[ 0.000000] .init : 0xc0621000 - 0xc0657a80 ( 219 kB)
[ 0.000000] .data : 0xc0658000 - 0xc069f840 ( 287 kB)
[ 0.000000] .bss : 0xc069f864 - 0xc0741d8c ( 650 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:292
[ 0.000000] arm-freq-id: 7
[ 0.000000] parent rate 25000000, x: 83886081
[ 0.000000] after shitf - current x: 2000000023
[ 0.000000] ARMPLL0: pdev: 1, ndev: 80, ndiv_frac: 1, mdiv: 4, rate: 2000000023
[ 0.000000] arm-freq-id: 7
[ 0.000000] arm-freq-id: 7
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[ 0.010000] Calibrating delay loop... 1993.93 BogoMIPS (lpj=9969664)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Security Framework initialized
[ 0.070000] AppArmor: AppArmor initialized
[ 0.070000] Mount-cache hash table entries: 512
[ 0.070000] CPU: Testing write buffer coherency: ok
[ 0.070000] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.070000] smp_twd: clock not found: -2
[ 0.070000] Calibrating local timer... 499.73MHz.
[ 0.140000] is_northstar_plus_b0: 1064 bcede230
[ 0.140000] Setting up static identity map for 0x614d0ff8 - 0x614d1050
[ 0.140000] L310 cache controller enabled
[ 0.140000] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x7a150801, Cache size: 524288 B
[ 0.140000] NorthStar+ B0 or later checking coherent mode
[ 0.140000] NorthStar+ B0 or later entering coherent mode
[ 0.140000] PCIe_0.RC ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] PCIe_0.EP ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] PCIe_1.RC ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] PCIe_1.EP ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] PCIe_2.RC ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] PCIe_2.EP ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] I2S ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] A9JTAG ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] SDIO ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] AMAC_0 ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] AMAC_1 ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] FA_AMAC_0 ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] FA_AMAC_1 ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] PAE ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] DMAC ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] USB3 ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] USB2 ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] SATA ARUSER=03 AWUSER=03 ARCACHE=B AWCACHE=7
[ 0.140000] ARMCore_M0_IO_CONTROL_DIRECT 18100408: 00632C03 00632C03
[ 0.140000] DDR_S1_IDM_IO_CONTROL_DIRECT 18109408: 619010B9 619010B9
[ 0.140000] DDR_S2_IDM_IO_CONTROL_DIRECT 1810A408: 7C000016 7C000016
[ 0.140000] PAXB_0_PCIE_RC_AXI_CONFIG 18012100: 0001C763 0001C763
[ 0.140000] PAXB_0_PCIE_EP_AXI_CONFIG 18012104: 0001C763 0001C763
[ 0.140000] PAXB_1_PCIE_RC_AXI_CONFIG 18013100: 0001C763 0001C763
[ 0.140000] PAXB_1_PCIE_EP_AXI_CONFIG 18013104: 0001C763 0001C763
[ 0.140000] PAXB_2_PCIE_RC_AXI_CONFIG 18014100: 0001C763 0001C763
[ 0.140000] PAXB_2_PCIE_EP_AXI_CONFIG 18014104: 0001C763 0001C763
[ 0.140000] I2S_M0_IDM_IO_CONTROL_DIRECT 18118408: 037B0181 037B0181
[ 0.140000] A9JTAG_M0_IDM_IO_CONTROL_DIRECT 18119408: 403B20DF 403B20DF
[ 0.140000] APBW_IDM_IDM_IO_CONTROL_DIRECT 18131408: 0B737FFF 0B737FFF
[ 0.140000] SDIO_IDM_IO_CONTROL_DIRECT 18117408: 1B800001 1B800001
[ 0.140000] AMAC_IDM0_IO_CONTROL_DIRECT 18110408: 063B03C5 063B03C5
[ 0.140000] AMAC_IDM1_IO_CONTROL_DIRECT 18111408: 063B03C5 063B03C5
[ 0.140000] FA_AMAC_IDM0_IO_CONTROL_DIRECT 18112408: 063B03C5 063B03C5
[ 0.140000] FA_AMAC_IDM1_IO_CONTROL_DIRECT 18113408: 063B03C5 063B03C5
[ 0.140000] PAE_M0_IDM_IO_CONTROL_DIRECT 1811F408: 037B018D 037B018D
[ 0.140000] DMAC_M0_IDM_IO_CONTROL_DIRECT 18114408: 0000F003 0000F003
[ 0.140000] USB3_IDM_IDM_IO_CONTROL_DIRECT 18104408: 000002DD 000002DD
[ 0.140000] USB2_IDM_IDM_IO_CONTROL_DIRECT 18115408: 000002DD 000002DD
[ 0.140000] SATA_M0_IDM_IO_CONTROL_DIRECT 1811E408: 007B018D 007B018D
[ 0.140000] ACPAL: preliminary scan on init
[ 0.140000] ACPAL: preliminary scan complete
[ 0.140000] ACPAL: fault handler has been registered & enabled
[ 0.140000] AXIIC_REMAP 1A000000 = 00000001
[ 0.140000] NorthStar+ B0 or later entered coherent mode
[ 0.140000] CPU1: Booted secondary processor
[ 0.140000]
[ 0.140000] <enable_a9_features> CUP_ID 1 a9_aux = 0x41; a9_aux_m = 0x4f; a9_sys = 0x10c53c7d
[ 0.140000]
[ 0.140000] <enable_a9_features> CUP_ID 0 a9_aux = 0x41; a9_aux_m = 0x4f; a9_sys = 0x10c53c7d
[ 0.200000] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.200000] Brought up 2 CPUs
[ 0.200000] SMP: Total of 2 processors activated (3987.86 BogoMIPS).
[ 0.200000] devtmpfs: initialized
[ 0.200000] NET: Registered protocol family 16
[ 0.200000] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.200000] GENPLL[5] mdiv=12 rate=1500000000
[ 0.200000] Sel=1 Ovr=0 Div=2
[ 0.200000] UART clock rate 62500000
[ 0.200000] IDM: set up timeout/fault detection
[ 0.200000] IDM: preliminary scan on init
[ 0.200000] IDM: preliminary scan complete
[ 0.200000] IDM: set IHOST_S0 to 0000033A, read back 0000033A
[ 0.200000] IDM: set IHOST_S1 to 0000033A, read back 0000033A
[ 0.200000] IDM: set DDR_S1 to 0000033A, read back 0000033A
[ 0.200000] IDM: set DDR_S2 to 0000033A, read back 0000033A
[ 0.200000] IDM: set AXI_PCIE_S0_IDM to 0000033A, read back 0000033A
[ 0.200000] IDM: set AXI_PCIE_S1_IDM to 0000033A, read back 0000033A
[ 0.200000] IDM: set CMICD_S0_IDM to 0000033A, read back 0000033A
[ 0.200000] IDM: set APBY_S0_IDM to 0000033A, read back 0000033A
[ 0.200000] IDM: set ROM_S0 to 0000033A, read back 0000033A
[ 0.200000] IDM: set NAND_IDM to 0000033A, read back 0000033A
[ 0.200000] IDM: set QSPI_IDM to 0000033A, read back 0000033A
[ 0.200000] IDM: set A9JTAG_S0_IDM to 0000033A, read back 0000033A
[ 0.200000] IDM: set SRAM_S0 to 0000033A, read back 0000033A
[ 0.200000] IDM: set APBZ_S0_IDM to 0000033A, read back 0000033A
[ 0.200000] IDM: set APBV_S0_IDM to 0000033A, read back 0000033A
[ 0.200000] IDM: set AXIIC_DS_3 to 0000033A, read back 0000033A
[ 0.200000] IDM: set AXIIC_DS_4 to 0000033A, read back 0000033A
[ 0.200000] IDM: set PAE_S0_IDM to 0000033A, read back 0000033A
[ 0.200000] IDM: set APBW_IDM to 0000033A, read back 0000033A
[ 0.200000] IDM: set APBX_IDM to 0000033A, read back 0000033A
[ 0.200000] IDM: set APBR_IDM to 0000033A, read back 0000033A
[ 0.200000] IDM: set AXIIC_DS_0 to 0000033A, read back 0000033A
[ 0.200000] IDM: set AXIIC_DS_1 to 0000033A, read back 0000033A
[ 0.200000] IDM: fault/timeout detection setup complete
[ 0.200000] L2C: Set up L2C error detection
[ 0.200000] L2C: previous interrupt mask = 00000000
[ 0.200000] L2C: current interrupt mask = 00000000
[ 0.200000] L2C: error detection setup complete
[ 0.200000] board_init: 1887 bcede230
[ 0.200000] Onboard 'iproc-smb' 0 will run in coherent mode
[ 0.200000] Onboard 'bcm-ehci' 0 will run in coherent mode
[ 0.200000] Onboard 'bcm-ohci' 0 will run in coherent mode
[ 0.200000] setup_sdio: 752 fed17800
[ 0.200000] Onboard 'iproc-sdio' 0 will run in coherent mode
[ 0.200000] Synology RT1900ac Hardware Init
[ 0.200000] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.200000] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.210000] bio: create slab <bio-0> at 0
[ 0.210000] SCSI subsystem initialized
[ 0.210000] usbcore: registered new interface driver usbfs
[ 0.220000] usbcore: registered new interface driver hub
[ 0.220000] usbcore: registered new device driver usb
[ 0.220000] Switching to clocksource iproc_gtimer
[ 0.220000] cfg80211: Calling CRDA to update world regulatory domain
[ 0.220000] AppArmor: AppArmor Filesystem Enabled
[ 0.220000] NET: Registered protocol family 2
[ 0.220000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.220000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.220000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.220000] TCP: reno registered
[ 0.220000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.220000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.220000] NET: Registered protocol family 1
[ 0.220000] RPC: Registered named UNIX socket transport module.
[ 0.220000] RPC: Registered udp transport module.
[ 0.220000] RPC: Registered tcp transport module.
[ 0.220000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.220000] Trying to unpack rootfs image as initramfs...
[ 2.380000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 2.400000] Freeing initrd memory: 3516K
[ 2.400000] Broadcom IPROC RNG Driver
[ 2.410000] libphy: iproc_ccb_mdiobus: probed
[ 2.420000] libphy: iproc_ccb_mdiobus: probed
[ 2.420000] Broadcom IPROC GSIO-SPI Driver
[ 2.420000] bcm5301x_spi bcm5301x_spi: master is unqueued, this is deprecated
[ 2.420000] NVRAM: map 0x1e0e0000
[ 2.540000] mmc0: SDHCI controller on BCM-SDIO [iproc-sdio.0] using ADMA
[ 2.540000] iproc_pwmc_probe iobase fec31000 phys:18031000
[ 2.540000] iproc gpiochip add GPIOA
[ 2.540000] GPIOA:ioaddr fec00060
[ 2.540000] GPIOA:intr_ioaddr fec00000 dmu_ioaddr fec20000
[ 2.540000] Initial usb2h clock is: 000002dd
[ 2.540000] Initial usb2h clock now is: 000002dd
[ 2.540000] Initial usb2_reset_state is: 00000000
[ 2.580000] WrongPCIGen2TemplateWAR: 1768 00000190 507e8630 604e0000 00000000 504e0190
[ 2.620000] get EXT CSD retry count: [0]
[ 2.620000] mmc0: BKOPS_EN bit is not set
[ 2.620000] WrongPCIGen2TemplateWAR: 1768 00000191 507e8630 60660000 00000000 50660191
[ 2.620000] mmc0: new high speed MMC card at address 0001
[ 2.870000] PCIE0: LINKSTA reg 0xbe val 0x9012
[ 2.870000] reg[0xac]=0x10, reg[0xae]=0x42, reg[0xb0]=0x8000, reg[0xb4]=0x2c10, reg[0xb6]=0x10, reg[0xb8]=0x5c12, reg[0xba]=0x65, reg[0xbe]=0x9012, reg[0xc6]=0x40, reg[0xca]=0x1, reg[0xd0]=0x1f, reg[0xd2]=0x8, reg[0xdc]=0x2, PCIE0 link=1
[ 2.870000] soc_pcie_init: 1950 00000000 fec12208
[ 2.870000] soc_pcie_init: 1958 0000003f
[ 2.870000] PCI host bridge to bus 0000:00
[ 2.870000] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fffffff]
[ 2.870000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 2.870000] PCI: bus0: Fast back to back transfers disabled
[ 2.870000] PCI: bus1: Fast back to back transfers disabled
[ 2.870000] PCIe 0000:00:00.0 14E4.8022 will run in coherent mode
[ 2.870000] PCIe 0000:01:00.0 14E4.43A1 will run in coherent mode
[ 2.870000] PCIe map irq: 0000:00:00.00 slot 0, pin 1, irq: 163
[ 2.870000] PCIe map irq: 0000:01:00.00 slot 0, pin 1, irq: 163
[ 2.870000] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x082fffff]
[ 2.870000] pci 0000:01:00.0: BAR 2: assigned [mem 0x08000000-0x081fffff 64bit]
[ 2.870000] pci 0000:01:00.0: BAR 0: assigned [mem 0x08200000-0x08207fff 64bit]
[ 2.870000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.870000] pci 0000:00:00.0: bridge window [mem 0x08000000-0x082fffff]
[ 2.870000] PCI: enabling device 0000:00:00.0 (0146 -> 0147)
[ 2.910000] WrongPCIGen2TemplateWAR: 1768 00000190 50fe8630 60ce0000 00000001 50ce0190
[ 2.950000] WrongPCIGen2TemplateWAR: 1768 00000191 50fe8630 60e60000 00000001 50e60191
[ 3.200000] PCIE1: LINKSTA reg 0xbe val 0x9012
[ 3.200000] reg[0xac]=0x10, reg[0xae]=0x42, reg[0xb0]=0x8000, reg[0xb4]=0x2c10, reg[0xb6]=0x10, reg[0xb8]=0x5c12, reg[0xba]=0x65, reg[0xbe]=0x9012, reg[0xc6]=0x40, reg[0xca]=0x1, reg[0xd0]=0x1f, reg[0xd2]=0x8, reg[0xdc]=0x2, PCIE1 link=1
[ 3.200000] soc_pcie_init: 1950 00000000 fec13208
[ 3.200000] soc_pcie_init: 1958 0000003f
[ 3.200000] PCI host bridge to bus 0001:00
[ 3.200000] pci_bus 0001:00: root bus resource [mem 0x40000000-0x47ffffff]
[ 3.200000] pci_bus 0001:00: No busn resource found for root bus, will use [bus 00-ff]
[ 3.200000] PCI: bus0: Fast back to back transfers disabled
[ 3.200000] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.200000] PCI: bus1: Fast back to back transfers disabled
[ 3.200000] PCIe 0001:00:00.0 14E4.8022 will run in coherent mode
[ 3.200000] PCIe 0001:01:00.0 14E4.43A2 will run in coherent mode
[ 3.200000] PCIe map irq: 0000:00:00.00 slot 0, pin 1, irq: 163
[ 3.200000] PCIe map irq: 0000:01:00.00 slot 0, pin 1, irq: 163
[ 3.200000] PCIe map irq: 0001:00:00.00 slot 0, pin 1, irq: 169
[ 3.200000] PCIe map irq: 0001:01:00.00 slot 0, pin 1, irq: 169
[ 3.200000] pci 0001:00:00.0: BAR 8: assigned [mem 0x40000000-0x402fffff]
[ 3.200000] pci 0001:01:00.0: BAR 2: assigned [mem 0x40000000-0x401fffff 64bit]
[ 3.200000] pci 0001:01:00.0: BAR 0: assigned [mem 0x40200000-0x40207fff 64bit]
[ 3.200000] pci 0001:00:00.0: PCI bridge to [bus 01]
[ 3.200000] pci 0001:00:00.0: bridge window [mem 0x40000000-0x402fffff]
[ 3.200000] PCI: enabling device 0001:00:00.0 (0140 -> 0143)
[ 3.240000] WrongPCIGen2TemplateWAR: 1768 00000000 57fe8630 67ce0000 00000002 57ce0190
[ 3.280000] WrongPCIGen2TemplateWAR: 1785 00000000 57fe8630 67ce0000 00000002 57ce0190
[ 3.320000] WrongPCIGen2TemplateWAR: 1768 00000000 57fe8630 67e60000 00000002 57e60191
[ 3.360000] WrongPCIGen2TemplateWAR: 1785 00000000 57fe8630 67e60000 00000002 57e60191
[ 3.610000] PCIE2: LINKSTA reg 0xbe val 0x1001
[ 3.610000] reg[0xac]=0x10, reg[0xae]=0x42, reg[0xb0]=0x8000, reg[0xb4]=0x2c10, reg[0xb6]=0x10, reg[0xb8]=0x5c12, reg[0xba]=0x65, reg[0xbe]=0x1001, reg[0xc6]=0x40, reg[0xca]=0x1, reg[0xd0]=0x1f, reg[0xd2]=0x8, reg[0xdc]=0x2, reg[0xde]=0x1, PCIE2 link=0
[ 3.710000] GENPLL[5] mdiv=12 rate=1500000000
[ 3.710000] sp805-wdt sp805-wdt: registration successful
[ 3.710000] sp805-wdt sp805-wdt: timtout=60 sec, nowayout=0
[ 3.730000] Registering iproc_pmu_device
[ 3.730000] audit: initializing netlink socket (disabled)
[ 3.730000] type=2000 audit(3.720:1): initialized
[ 3.740000] NFS: Registering the id_resolver key type
[ 3.740000] Key type id_resolver registered
[ 3.740000] Key type id_legacy registered
[ 3.740000] fuse init (API version 7.20)
[ 3.740000] msgmni has been set to 460
[ 3.740000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 3.740000] io scheduler noop registered
[ 3.740000] io scheduler cfq registered (default)
[ 3.740000] HDLC line discipline maxframe=4096
[ 3.740000] N_HDLC line discipline registered.
[ 3.740000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 3.740000] serial8250.0: ttyS0 at MMIO 0x18000300 (irq = 117) is a 16550A
[ 5.290000] console [ttyS0] enabled
[ 5.300000] brd: module loaded
[ 5.300000] st: Version 20101219, fixed bufsize 32768, s/g segs 256
[ 5.310000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.310000] USBH_usb2h_axi_m_AxUSER_cfg 1802A600: 000000C3 000000C3
[ 5.320000] bcm-ehci bcm-ehci.0: bcm-ehci
[ 5.320000] bcm-ehci bcm-ehci.0: new USB bus registered, assigned bus number 1
[ 5.330000] bcm-ehci bcm-ehci.0: irq 111, io mem 0xfec2a000
[ 5.360000] bcm-ehci bcm-ehci.0: USB 2.0 started, EHCI 1.00
[ 5.360000] hub 1-0:1.0: USB hub found
[ 5.360000] hub 1-0:1.0: 2 ports detected
[ 5.370000] bcm-ehci bcm-ehci.0: probe done
[ 5.370000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.380000] USBH_usb2h_axi_m_AxUSER_cfg 1802A600: 000000C3 000000C3
[ 5.390000] bcm-ohci bcm-ohci.0: bcm-ohci
[ 5.390000] bcm-ohci bcm-ohci.0: new USB bus registered, assigned bus number 2
[ 5.400000] bcm-ohci bcm-ohci.0: irq 111, io mem 0xfec2b000
[ 5.460000] hub 2-0:1.0: USB hub found
[ 5.460000] hub 2-0:1.0: 2 ports detected
[ 5.470000] bcm-ohci bcm-ohci.0: probe done
[ 5.470000] Initializing USB Mass Storage driver...
[ 5.480000] usbcore: registered new interface driver usb-storage
[ 5.480000] USB Mass Storage support registered.
[ 5.490000] i2c /dev entries driver
[ 5.490000] mmcblk0: mmc0:0001 004GE0 3.68 GiB
[ 5.500000] mmcblk0boot0: mmc0:0001 004GE0 partition 1 2.00 MiB
[ 5.500000] mmcblk0boot1: mmc0:0001 004GE0 partition 2 2.00 MiB
[ 5.510000] mmcblk0: p1 p3 p4 < p5 p6 p7 >
[ 5.520000] mmcblk0boot1: unknown partition table
[ 5.530000] mmcblk0boot0: unknown partition table
[ 5.530000] sdhci: Secure Digital Host Controller Interface driver
[ 5.540000] sdhci: Copyright(c) Pierre Ossman
[ 5.540000] usbcore: registered new interface driver usbhid
[ 5.550000] usbhid: USB HID core driver
[ 5.550000] Netfilter messages via NETLINK v0.30.
[ 5.560000] nf_conntrack version 0.5.0 (16384 buckets, 131072 max)
[ 5.560000] ctnetlink v0.93: registering with nfnetlink.
[ 5.570000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 5.570000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 5.580000] ip_set: protocol 6
[ 5.580000] IPv4 over IPSec tunneling driver
[ 5.590000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.590000] arp_tables: (C) 2002 David S. Miller
[ 5.600000] TCP: cubic registered
[ 5.600000] TCP: highspeed registered
[ 5.610000] Initializing XFRM netlink socket
[ 5.610000] NET: Registered protocol family 10
[ 5.620000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 5.620000] sit: IPv6 over IPv4 tunneling driver
[ 5.630000] NET: Registered protocol family 17
[ 5.630000] NET: Registered protocol family 15
[ 5.640000] Bridge firewalling registered
[ 5.640000] Ebtables v2.0 registered
[ 5.640000] 8021q: 802.1Q VLAN Support v1.8
[ 5.650000] Key type dns_resolver registered
[ 5.650000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 5.660000] GENPLL[5] mdiv=12 rate=1500000000
[ 5.660000] qspi_iproc qspi_iproc.1: 1-lane output, 3-byte address
[ 5.670000] m25p80 spi1.0: m25p80 (1024 Kbytes)
[ 5.670000] Searching for RedBoot partition table in spi1.0 at offset 0xf0000
[ 5.690000] 5 RedBoot partitions found on MTD device spi1.0
[ 5.700000] Creating 5 MTD partitions on "spi1.0":
[ 5.700000] 0x000000000000-0x0000000b0000 : "RedBoot"
[ 5.710000] 0x0000000b0000-0x0000000d0000 : "shmoo"
[ 5.710000] 0x0000000d0000-0x0000000e0000 : "vendor"
[ 5.720000] vender Mac4 checksum error ucSum:0xa1 Buf:0x3d Sum:161.
[ 5.730000] vender Mac5 checksum error ucSum:0x80 Buf:0x4e Sum:384.
[ 5.730000] vender Mac6 checksum error ucSum:0x24 Buf:0x2c Sum:292.
[ 5.740000] usb 1-1: new high-speed USB device number 2 using bcm-ehci
[ 5.740000] vender Mac7 checksum error ucSum:0x7f Buf:0x34 Sum:383.
[ 5.750000] serial number='16C0NXN040000'
[ 5.760000] WPS pin='58048573'
[ 5.760000] 0x0000000e0000-0x0000000f0000 : "RedBoot Config"
[ 5.770000] 0x0000000f0000-0x000000100000 : "FIS directory"
[ 5.770000] bcm5301x_gmac_init_module: NAPI2_POLL mode
[ 5.780000] bcm5301x_gmac_init_module: et_rx_rate_limit set to 0x1
[ 5.780000] bcm5301x_gmac_probe enter name:bcmiproc-gmac0; id:0x0; unit:0
[ 5.790000] si_doattach chipid: 0x3f04cf1e
[ 5.790000] et0: base_addr (0x18022000) irq (179)
[ 5.800000] etc_gmac_speed default GMAC0 speed: auto
[ 5.800000] etc_attach() mdio_init_time = 5
[ 5.810000] si_doattach: incoming bus is PCI but it's a lie, switching to SI devid:0xcf1c
[ 5.820000] si_doattach chipid: 0x3f04cf1e
[ 5.820000] si_attach socitype(0x3) chip(0xcf1e) chiprev(0x4) chippkg(0x0)
[ 5.830000] et0: chipattach: phyaddr(0x1e)
[ 5.830000] ctf ipc hash bucket size=16384, allocated size=65536
[ 5.840000] bcm5301x_gmac_probe: et->cih not NULL
[ 5.840000] bcm5301x_gmac_probe: CTF_ENAB(ci) = 1
[ 5.850000] et0: Enable Checksum-SG
[ 5.850000] bcmiproc-gmac0 bcmiproc-gmac0: eth0: mixed HW and IP checksum settings.
[ 5.860000] eth0: Broadcom BCM5302x 10/100/1000 Mbps Ethernet Controller 6.30.40 (TOB) (r)
[ 5.870000] eth_mac_proc_create: enter
[ 5.870000] BRCM TAG enabled
[ 5.870000] et_ctf_active disabled
[ 5.880000] bcm5301x_gmac_probe enter name:bcmiproc-gmac1; id:0x0; unit:1
[ 5.890000] et1: base_addr (0x18023000) irq (180)
[ 5.890000] etc_gmac_speed default GMAC1 speed: auto
[ 5.890000] etc_attach() mdio_init_time = 5
[ 5.900000] si_doattach: incoming bus is PCI but it's a lie, switching to SI devid:0xcf1c
[ 5.910000] si_doattach chipid: 0x3f04cf1e
[ 5.910000] si_attach socitype(0x3) chip(0xcf1e) chiprev(0x4) chippkg(0x0)
[ 5.920000] et1: chipattach: phyaddr(0x1e)
[ 5.920000] bcm5301x_gmac_probe: et->cih not NULL
[ 5.930000] bcm5301x_gmac_probe: CTF_ENAB(ci) = 1
[ 5.930000] et1: Enable Checksum-SG
[ 5.940000] bcmiproc-gmac1 bcmiproc-gmac1: eth1: mixed HW and IP checksum settings.
[ 5.940000] eth1: Broadcom BCM5302x 10/100/1000 Mbps Ethernet Controller 6.30.40 (TOB) (r)
[ 5.950000] eth_mac_proc_create: enter
[ 5.960000] BRCM TAG enabled
[ 5.960000] et_ctf_active disabled
[ 5.960000] scsi0 : usb-storage 1-1:1.0
[ 5.960000] bcm5301x_gmac_probe enter name:bcmiproc-gmac2; id:0x0; unit:2
[ 5.960000] et2: base_addr (0x18024000) irq (181)
[ 5.960000] etc_gmac_speed default GMAC2 speed: auto
[ 5.960000] etc_attach() mdio_init_time = 5
[ 5.960000] si_doattach: incoming bus is PCI but it's a lie, switching to SI devid:0xcf1c
[ 5.960000] si_doattach chipid: 0x3f04cf1e
[ 5.960000] si_attach socitype(0x3) chip(0xcf1e) chiprev(0x4) chippkg(0x0)
[ 5.960000] et2: chipattach: phyaddr(0x1e)
[ 5.960000] et2: chipattach: Calling robo attach
[ 5.960000] bcm_robo_attach: devid32: 0x2
[ 5.960000] et2: chipattach: bringing up robo switch
[ 5.960000]
[ 5.960000] chipattach SKIP [Disabling Pause Pass Through, Set flood on imp port, and enable egress port on imp port]
[ 5.960000]
[ 5.960000] Configuring Robo VLANs
[ 5.960000] bcm_robo_enable_switch OTP: offset 0x0f = 0x800
[ 5.960000] bcm_robo_enable_switch Northstar Family chip
[ 5.960000] bcm_robo_enable_switch Setting switch max frame size to 2500
[ 5.960000] bcm_robo_enable_switch Setting Jumbo enable for all ports
[ 5.960000] bcm_robo_enable_switch Setting switch max frame size to 10240
[ 5.960000] bcm5301x_gmac_probe: et->cih not NULL
[ 5.960000] bcm5301x_gmac_probe: CTF_ENAB(ci) = 1
[ 5.960000]
[ 5.960000] Enabling checksum offload ...
[ 5.960000] et2: Enable Checksum-SG
[ 5.960000] bcmiproc-gmac2 bcmiproc-gmac2: eth2: mixed HW and IP checksum settings.
[ 5.960000] eth2: Broadcom BCM5302x 10/100/1000 Mbps Ethernet Controller 6.30.40 (TOB) (r)
[ 5.960000] eth_mac_proc_create: enter
[ 5.960000]
[ 5.960000] Creating fa bypass proc entry
[ 5.960000] BRCM TAG enabled
[ 5.960000] et_ctf_active enabled
[ 5.960000] bcm5301x_gmac_probe enter name:bcmiproc-gmac3; id:0x0; unit:3
[ 5.960000] et3: base_addr (0x18025000) irq (182)
[ 5.960000] etc_gmac_speed default GMAC3 speed: auto
[ 5.960000] etc_attach() mdio_init_time = 5
[ 5.960000] si_doattach: incoming bus is PCI but it's a lie, switching to SI devid:0xcf1c
[ 5.960000] si_doattach chipid: 0x3f04cf1e
[ 5.960000] si_attach socitype(0x3) chip(0xcf1e) chiprev(0x4) chippkg(0x0)
[ 5.960000] et3: chipattach: phyaddr(0x1e)
[ 5.960000] bcm5301x_gmac_probe: et->cih not NULL
[ 5.960000] bcm5301x_gmac_probe: CTF_ENAB(ci) = 1
[ 5.960000] et3: Enable Checksum-SG
[ 5.960000] bcmiproc-gmac3 bcmiproc-gmac3: eth3: mixed HW and IP checksum settings.
[ 5.960000] eth3: Broadcom BCM5302x 10/100/1000 Mbps Ethernet Controller 6.30.40 (TOB) (r)
[ 5.960000] eth_mac_proc_create: enter
[ 5.960000] BRCM TAG enabled
[ 5.960000] et_ctf_active enabled
[ 5.960000] registered taskstats version 1
[ 6.210000] RAMDISK: lzma image found at block 0
[ 6.360000] usb 1-2: new high-speed USB device number 3 using bcm-ehci
[ 6.550000] scsi1 : usb-storage 1-2:1.0
[ 7.210000] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6
[ 7.210000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 7.220000] sd 0:0:0:0: [sdr] 30031872 512-byte logical blocks: (15.3 GB/14.3 GiB)
[ 7.230000] sd 0:0:0:0: [sdr] Write Protect is off
[ 7.240000] sd 0:0:0:0: [sdr] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 7.250000] sdr: sdr1
[ 7.260000] sd 0:0:0:0: [sdr] Attached SCSI removable disk
[ 7.570000] scsi 1:0:0:0: Direct-Access Generic STORAGE DEVICE 9910 PQ: 0 ANSI: 0
[ 7.580000] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 7.580000] scsi 1:0:0:1: Direct-Access Generic STORAGE DEVICE 9910 PQ: 0 ANSI: 0
[ 7.590000] sd 1:0:0:0: [sdq] Attached SCSI removable disk
[ 7.600000] scsi 1:0:0:1: Attached scsi generic sg2 type 0
[ 8.660000] VFS: Mounted root (ext2 filesystem) on device 1:0.
START /linuxrc.syno
Insert basic USB modules...
[ 8.780000] rt1900ac_synobios: module license 'Synology Inc.' taints kernel.
[ 8.790000] Disabling lock debugging due to kernel taint
[ 8.800000] 2023-1-1 0:0:0 UTC
[ 8.800000] synobios: load, major number 201
[ 8.800000] Brand: Synology
[ 8.810000] Model: RT-1900ac
[ 8.810000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 8.820000] synobios cpu_arch proc entry initialized
[ 8.820000] synobios crypto_hw proc entry initialized
[ 8.830000] synobios syno_platform proc entry initialized
mknod: /dev/synobios: File exists
Starting /usr/syno/bin/synocfgen...
unknown model: 176, skip updating model info
/usr/syno/bin/synocfgen returns 0
[ 8.850000] synobios: unload
Partition Version=8
/sbin/e2fsck exists, checking /dev/sda5...
1.42.6-6022: recovering journal
23461 inodes used (29.92%, out of 78400)
180 non-contiguous files (0.8%)
12 non-contiguous directories (0.1%)
# of inodes with ind/dind/tind blocks: 0/0/0
Extent depth histogram: 19237/53
254983 blocks used (81.37%, out of 313344)
0 bad blocks
1 large f[ 11.660000] EXT4-fs (mmcblk0p5): barriers disabled
ile
17157 regular file[ 11.670000] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts:
s
1916 directories
84 character device files
1613 block device files
0 fifos
1019 links
2681 symbolic links (2465 fast symbolic links)
1 socket
------------
24471 files
/sbin/e2fsck returns 1
Mounting /dev/sda5 /tmpRoot
------------upgrade
/etc/upgrade.sh: line 80: support_internal_usb_vol: not found
use default /dev/sda6
Begin upgrade procedure
e2fsck 1.42.6 (21-Sep-2012)
Mount data partition
/bin/mount /dev/sda6 /tmpData
[ 11.870000] EXT4-fs (mmcblk0p6): barriers disabled
[ 12.230000] EXT4-fs (mmcblk0p6): recovery complete
[ 12.230000] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts:
No upgrade file exists
End upgrade procedure
============upgrade
Wait 2 seconds for synology manufactory device
mount: open failed, msg:No medium found
mount: mounting /dev/sdq on /mnt failed: No such device
Sun Jan 1 00:00:05 UTC 2023
/dev/sda5 /tmpRoot ext4 rw,relatime,journal_checksum,data=ordered 0 0
none /sys/kernel/debug debugfs rw,relatime 0 0
none /sys sysfs rw,relatime 0 0
linuxrc.syno ex[ 14.720000] EXT3-fs (mmcblk0p5): error: couldn't mount because of unsupported optional features (240)
ecuted successfully.
[ 14.850000] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: barrier=1
[ 14.860000] VFS: Mounted root (ext4 filesystem) on device 179:5.
[ 14.870000] Trying to move old root to /initrd ... okay
[ 14.890000] devtmpfs: mounted
[ 14.890000] Freeing init memory: 216K
[ 15.720000] EXT4-fs (mmcblk0p5): re-mounted. Opts: (null)
[ 16.810000] init: synomeshsessioncheck main process (1048) terminated with status 1
==================== start udevd ====================
[ 19.580000] init: syno-auth-check main process (1337) killed by TERM signal
[ 20.720000] systemd-udevd[1743]: starting version 204
===== trigger device plug event =====
[ 21.050000] 2021-1-1 0:0:0 UTC
[ 21.060000] synobios: load, major number 201
[ 21.060000] Brand: Synology
[ 21.060000] Model: RT-1900ac
[ 21.070000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 21.080000] synobios cpu_arch proc entry initialized
[ 21.080000] synobios crypto_hw proc entry initialized
[ 21.090000] synobios syno_platform proc entry initialized
[ 23.170000] wl_module_init: passivemode set to 0x0
[ 23.180000] wl_module_init: txworkq set to 0x1
[ 23.220000] wlc_exclude_chans_attach: skip forbidden channel 120
[ 23.220000] wlc_exclude_chans_attach: skip forbidden channel 124
[ 23.230000] wlc_exclude_chans_attach: skip forbidden channel 128
[ 23.230000] wlc_exclude_chans_attach: skip forbidden channel 144
[ 23.240000] wlc_exclude_chans_attach(220)
[ 23.250000] def: US/140
[ 23.250000] def: US/140
[ 23.260000] wlan0: Broadcom BCM43a1 802.11 Wireless Controller 7.35.85_e2.1.1 (r488525)
[ 23.270000] PCI: enabling device 0001:01:00.0 (0140 -> 0142)
[ 23.310000] wlc_exclude_chans_attach: skip forbidden channel 120
[ 23.310000] wlc_exclude_chans_attach: skip forbidden channel 124
[ 23.320000] wlc_exclude_chans_attach: skip forbidden channel 128
[ 23.330000] wlc_exclude_chans_attach: skip forbidden channel 144
[ 23.330000] wlc_exclude_chans_attach(220)
[ 23.340000] def: US/140
[ 23.350000] def: US/140
[ 23.350000] wlan1: Broadcom BCM43a2 802.11 Wireless Controller 7.35.85_e2.1.1 (r488525)
[ 25.210000]
[ 25.210000] etc_up ==== Unit:0 UP
[ 25.220000] device eth0 entered promiscuous mode
[ 25.240000]
[ 25.240000] etc_up ==== Unit:1 UP
[ 25.250000] device eth1 entered promiscuous mode
[ 25.300000] br0: port 2(eth1) entered forwarding state
[ 25.300000] br0: port 2(eth1) entered forwarding state
[ 25.310000] br0: port 1(eth0) entered forwarding state
[ 25.310000] br0: port 1(eth0) entered forwarding state
[ 25.510000]
[ 25.510000] etc_down ==== Unit:0 DOWN
[ 25.510000] br0: port 1(eth0) entered disabled state
[ 25.550000]
[ 25.550000] etc_up ==== Unit:0 UP
[ 25.550000] br0: port 1(eth0) entered forwarding state
[ 25.560000] br0: port 1(eth0) entered forwarding state
[ 25.710000]
[ 25.710000] etc_down ==== Unit:1 DOWN
[ 25.720000] br0: port 2(eth1) entered disabled state
[ 25.740000]
[ 25.740000] etc_up ==== Unit:1 UP
[ 25.750000] br0: port 2(eth1) entered forwarding state
[ 25.750000] br0: port 2(eth1) entered forwarding state
[ 26.220000] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready
[ 26.560000] br0: port 1(eth0) entered forwarding state
[ 26.750000] br0: port 2(eth1) entered forwarding state
[ 31.350000] Init successfully
[ 32.020000] IPv6: ADDRCONF(NETDEV_UP): gbr0: link is not ready
[ 34.620000] bcm_robo_enable_switch OTP: offset 0x0f = 0x800
[ 34.620000] bcm_robo_enable_switch Northstar Family chip
[ 34.630000] bcm_robo_enable_switch Setting Jumbo enable for all ports
[ 34.640000] bcm_robo_enable_switch Setting switch max frame size to 10240
[ 48.140000] init: v6laninit main process (7349) terminated with status 255
[ 49.100000] Unhandled msg num 520d
[ 53.010000] EXT4-fs (mmcblk0p6): barriers disabled
[ 53.020000] EXT4-fs (mmcblk0p6): mounted filesystem with writeback data mode. Opts: data=writeback,oldalloc
[ 53.840000] Adding 262140k swap on /volume1/.intswp. Priority:999 extents:2 across:270332k SS
[ 54.420000] usbcore: registered new interface driver usblp
MufRouter login: [ 58.730000] encryptfs using the OCF package.
[ 61.250000] loop: module loadedAle... čo je toť toto tu na tom konci, čo som zámerne rozdeleu?
Code: Select all
[ 66.920000] mmcblk0: error -110 transferring data, sector 2242304, nr 1024, cmd response 0x900, card status 0x200b00
[ 66.930000] mmcblk0: retrying using single block read
[ 68.520000] mmcblk0: error -110 transferring data, sector 2242948, nr 380, cmd response 0x900, card status 0x0
[ 68.530000] end_request: I/O error, dev mmcblk0, sector 2242948
[ 69.880000] mmcblk0: error -110 transferring data, sector 2242949, nr 379, cmd response 0x900, card status 0x0
[ 69.890000] end_request: I/O error, dev mmcblk0, sector 2242949
[ 72.530000] mmcblk0: error -110 transferring data, sector 2242944, nr 8, cmd response 0x900, card status 0x200b00
[ 72.540000] mmcblk0: retrying using single block read
[ 78.770000] findhostd uses obsolete (PF_INET,SOCK_PACKET)
[ 83.630000] warning: `named' uses 32-bit capabilities (legacy support in use)
[ 85.710000] init: ipsec pre-start process (10568) terminated with status 3
[ 87.630000] mmcblk0: error -110 transferring data, sector 13092, nr 514, cmd response 0x900, card status 0x200b00
[ 87.640000] mmcblk0: retrying using single block read
[ 89.070000] mmcblk0: error -110 transferring data, sector 13286, nr 320, cmd response 0x900, card status 0x0
[ 89.080000] end_request: I/O error, dev mmcblk0, sector 13286
[ 90.430000] mmcblk0: error -110 transferring data, sector 13295, nr 311, cmd response 0x900, card status 0x0
[ 90.440000] end_request: I/O error, dev mmcblk0, sector 13295
[ 91.890000] mmcblk0: error -110 transferring data, sector 13550, nr 56, cmd response 0x900, card status 0x0
[ 91.900000] end_request: I/O error, dev mmcblk0, sector 13550
[ 93.280000] mmcblk0: error -110 transferring data, sector 13606, nr 514, cmd response 0x900, card status 0x200b00
[ 93.290000] mmcblk0: retrying using single block read
[ 94.670000] mmcblk0: error -110 transferring data, sector 13676, nr 444, cmd response 0x900, card status 0x0
[ 94.680000] end_request: I/O error, dev mmcblk0, sector 13676
[ 96.030000] mmcblk0: error -110 transferring data, sector 13677, nr 443, cmd response 0x900, card status 0x0
[ 96.040000] end_request: I/O error, dev mmcblk0, sector 13677
[ 97.440000] mmcblk0: error -110 transferring data, sector 13803, nr 317, cmd response 0x900, card status 0x0
[ 97.450000] end_request: I/O error, dev mmcblk0, sector 13803
[ 100.130000] mmcblk0: error -110 transferring data, sector 13548, nr 8, cmd response 0x900, card status 0x200b00
[ 100.140000] mmcblk0: retrying using single block read
[ 101.490000] mmcblk0: error -110 transferring data, sector 13550, nr 6, cmd response 0x900, card status 0x0
[ 101.500000] end_request: I/O error, dev mmcblk0, sector 13550
[ 102.850000] mmcblk0: error -110 transferring data, sector 13551, nr 5, cmd response 0x900, card status 0x0
[ 102.860000] end_request: I/O error, dev mmcblk0, sector 13551Po asi pátich minútach a nijakom extra posune (kedy som probuval tí ext2 partície mountuvať a dostával som celkom divné nezmyselné odpovede z mountuvačky) som si povedal, že šak keď fsck prešóv celkom rozumne, tak to možno už stihlo napraviť to, čo bolo doonďané.
Povedav som si, dám tomu reštart.
A veru... možná volačo z toho bude, Jožina sme asi našli zaťál furt živého.
Konečný konsenzus
Čo ja vím. Po reštarte sa z U-Bootu ozvalo toť toto:
Code: Select all
Press Ctrl+C to abort autoboot in 3 second
Reset Done
iproc_mmc_send_cmd() returned timeout
iproc_mmc_send_cmd() returned timeout
..Loading file "zImage" from mmc device 0:1
..............3388104 bytes read
.Loading file "rd.bin" from mmc device 0:1
................3596416 bytes read
## Booting kernel from Legacy Image at 61007fc0 ...
Image Name: Linux-3.6.11+
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3388040 Bytes = 3.2 MiB
Load Address: 61008000
Entry Point: 61008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 62007fc0 ...
Image Name: synology_northstarplus_rt1900ac
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 3596352 Bytes = 3.4 MiB
Load Address: 61008000
Entry Point: 61008000
Verifying Checksum ... OK
XIP Kernel Image ... OK
OK
boot_prep_linux commandline: console=ttyS0,115200 ip=off maxcpus=2 mem=240M initrd= root=/dev/mmcblk0p5 rootdelay=0 rw syno_hw_version=RT1900acv20 netif_num=2 syno_mac_address_mapping=eth0,eth1,wlan0,wlan1 wireless_num=2 rcutree.rcu_cpu_stall_suppress=1 syno_disable_usb3=1 flash_size=1
Starting kernel ...
Uncompressing Linux... done, booting the kernel.Tipujem že či tých 7 mesácov hluchoty čo to eMMC zažilo, či nedostalo z toho taký šok. Šok toho, že nebolo používané. Druhá vec je, že to je len 4GB a od januára 2018 do januára 2026 prešlo okolo 70 tisíc hodín za kerých ten router furt robeu voláke zápisy a prepisy do toho eMMCčka. Šak samozrejme klasika, štatistiky a také prkotiny.
- Ešte jenna fotka v rozebratom stave na záver, šak prečo ne.
Nevím, nejdem to vác rozebírať. Budem to sleduvať, budem ho používať.
Jenno je isté, podarilo sa mi ho dať do nastaveňá v jakom som ho mať stel a čil tak ostane až dotedy, dokedy ho neodstavím buď nafurt, alebo nepresunem o dům dál...
